N80 0.17Ω GeekVape Micro Mesh Coil & Cotton

Description

Purchase GeekVape Micro Mesh 0.17Ω Sheet Coils & Agleted Cotton Strips for Dense Cloud Production in the UAE

The GeekVape Zeus X Mesh RTA is built around a specific concept: replace the wound coil deck with a flat mesh sheet clamp system, and unlock a heating surface area that no wound coil at comparable resistance can match. The GeekVape Micro Mesh sheet coils are the consumable element of that system. Every GeekVape Zeus X Mesh RTA rebuild uses two components from this pack: the N80 mesh sheet that installs between the clamp posts in seconds, and the pre-cut cotton lace sized precisely for the Zeus X mesh plate that pushes through the clamp and into the juice channels in one motion. 

No wrapping, no screwdrivers for coil installation, no resistance checking before firing, the pre-cut mesh produces a consistent 0.17Ω reading on every install. Stock up from Vape Dubai for fast delivery across Dubai, Abu Dhabi, Sharjah, and the entire UAE.

Why Micro Mesh Outperforms Wound Coils in the Zeus X?

Surface Area: Micro Mesh makes full-face contact with the cotton, unlike wound coils that only touch at wrap points, resulting in a much larger vaporization area. This produces denser vapor and more intense flavor at the same 0.17Ω output.

Even Heat Distribution: The mesh sheet heats uniformly across its entire surface, reducing hotspots that are common in traditional wound coils. This lowers the risk of dry hits and delivers a more consistent vaping experience.

Installation Speed: Micro Mesh coils sheet installs in under two minutes by simply clamping the sheet and threading cotton, compared to 10-15 minutes for standard wire coil builds. The simplified process makes rebuilding significantly faster and more efficient.

Nichrome N80 Material, 50-70W, Dense Vapor

Nichrome 80 heats faster and requires less power to reach operating temperature than Kanthal at equivalent gauge. The lower resistance (0.17Ω) means more current and more heat per watt, producing denser, warmer vapor with a more assertive draw character. N80 Micro Mesh is described as producing “massive flavorful clouds”. The combination of faster ramp-up and higher surface area creates a draw that is immediately full and impactful from the first pulse.

Specs at a Glance

Spec	Detail
Material	Nichrome 80 (N80)
Resistance	0.17Ω
Wattage	50-70W
Architecture	Flat micro mesh sheet
Pack Contents	2 x mesh sheets + 2 x cotton laces
Compatible	GeekVape Zeus X Mesh RTA / ZX II
Vaping Style	DTL
Coil Format	Clamp-install (not wound)

Compatible Atomizers

The GeekVape Micro Mesh N80 0.17Ω sheet coil is designed exclusively for the GeekVape Zeus X Mesh RTA and the ZX II Mesh build deck. It is not compatible with standard wound coil RTA decks from GeekVape or other manufacturers, the mesh sheet dimensions are matched to the Zeus X clamp post spacing and will not fit standard post-hole decks.

Compatible E-Liquids

At 0.17Ω and 50-70W, the N80 Micro Mesh is a sub-ohm DTL build that requires high-VG freebase e-liquid. 70/30 VG/PG freebase at 3-6mg nicotine produces the optimal vapor density and flavor saturation this architecture is built for. 

What is Included in the Package?

• 2 x Geekvape Micro Mesh Coils 0.17Ω 
• 2 x Organic Cotton Strips with Agleted Ends
• 1 x User Guide

How to Install GeekVape Micro Mesh N80 in Your Zeus X

1. Remove the Zeus X Mesh RTA from your mod and unscrew the base to access the mesh deck
2. Loosen the two mesh clamp screws to open the clamp posts
3. Remove the spent mesh sheet by pulling it free from between the posts
4. Take a new N80 0.17Ω mesh sheet from the pack and position it flat between the clamp posts, centre the mesh across the airflow inlet
5. Tighten the clamp screws evenly, both sides simultaneously, until the mesh sheet is held firmly without over-compression
6. Read the resistance on your mod, should read approximately 0.17Ω
7. Dry burn at 15-20W only before wicking, pulse for 1-2 seconds to check for even glow across the mesh surface
8. Thread the included pre-cut cotton lace under and over the mesh sheet in the deck’s cotton channel, the lace is pre-sized for a snug fit
9. Trim the cotton tails to sit in the juice channels and saturate thoroughly with e-liquid
10. Begin vaping at 50W and increase to your preferred wattage within the 50-70W range

Stock Up Today From Vape Dubai

Two complete rebuilds per pack. N80 mesh for dense, cloud-forward DTL performance. Pre-cut cotton laces included. Fast installation, consistent 0.17Ω resistance every time. The dedicated replacement mesh for the GeekVape Zeus X RTA system. Place your order today on Vape Dubai.

FAQs

Does this Micro Mesh work with any RTA or only the Zeus X Mesh? 

These mesh sheets are dimensioned specifically for the GeekVape Zeus X Mesh RTA and ZX II Mesh build deck. They will not fit standard wound coil RTA decks, the sheet dimensions and clamp post spacing are unique to the Zeus X mesh system.

Is cotton included in the pack? 

Yes, each pack includes 2 mesh sheets and 2 pre-cut cotton laces sized precisely for the Zeus X mesh plate dimensions. No separate cotton purchase is required for two complete rebuilds.

What e-liquid should I use with N80 0.17Ω Micro Mesh? 

70/30 VG/PG freebase at 3-6mg nicotine. At 50-70W, high-VG liquid wicks correctly across the mesh surface and produces the dense vapor this architecture is built for. Avoid nicotine salt e-liquids at these wattages.

How long does each Micro Mesh sheet last? 

Lifespan varies with e-liquid sweetness and vaping frequency. GeekVape mesh sheets are rated for long-lasting use and can be cleaned by dry-burning at low wattage (15-20W) to remove residue when flavor degrades. Most daily users replace mesh sheets every 1-3 weeks depending on usage volume.